Mitutoyo 500-506-10, Digimatic Digital Caliper, 0 - 24"/600mm, .0005"/0.01mm, with SPC Output
Customers Score : Points of this product.
Product Brand : Mitutoyo
Product Model : 500-506-10
The Mitutoyo 500-506-10 ABSOLUTE 500 series digital caliper is especially adapted for measuring larger items. Its longer upper and lower jaws easily grasp these items to gauge and provide clear readings up to the maximum level of accuracy. It is made of durable hardened stainless steel to shield its components and for use anywhere in the workshop. It uses Mitutoyo’s ABSOLUTE linear encoder technology, which allows you to “set and forget” the origin and measure in awkward or difficult locations.
This digital caliper has large, .365-inch/9.7-mm LCD characters and easy-to-reach function control buttons, such as Inch/Metric to convert measurements, Origin to set and retain the original measuring point, On/Off to automatically shut off the caliper after 30 minutes, and Zero/ABS (Absolute Scale) to zero-set the LCD display. Its LCD readout can indicate measurements as small as 0.0005"/.01 mm, the minimum measurement for ID resolution.
Although identical to dial and vernier calipers in its ability to make precise measurements, the digital caliper also has the LCD, which clearly shows values and increases reading reliability over the other types. The LCD also reflects all ABSOLUTE system activities. The Absolute Scale (ABS) function tracks the origin point you set—even after shutoff. With the caliper on again, you can immediately start measuring, without zero resetting or worrying about overspeed errors. You can "zero out" the LCD before making and comparing incremental measurements without having to subtract the first measurement from the second.
The 500-506-10 has the ABSOLUTE electrostatic capacitance linear encoder. It weighs approximately 7.9 lbs (3583 g) and is made of hardened stainless steel construction. With its fixed and movable jaws, it has three-way measurement capability: outer diameter (OD), inner diameter (ID), and step, where the butt end of the fixed jaw measures one end of a work piece before its upper/lower or inner/outer "steps" are measured. Its jaws are longer, with Upper/Lower Jaw Length of 3.54/89.9 mm, Outside Jaw Depth of 3.54/89.9 mm, Inside Jaw Length of 1.85"/46.99 mm, and Inside Jaw Depth of 1.50 "/38.1 mm. Range is 0 to 24"/600mm, with OD Range of 0 to 24”/600mm and ID Range of .500" to 24"/600mm; LCD Resolution is .0005"/0.01mm, Repeatability is 0.0005-inch/0.01 mm, and Accuracy is rated at + or - .002"/.05 mm. Also included are origin-setting, zero-setting, inch-to-metric conversion, and on/off automatic shutoff function buttons. A Digital LCD Data Reading Hold function is available with the optional Data Hold Unit (959143), sold separately. An alarm alerts the user to low voltage and scale contamination and counting value composition errors. A thumb screw locks the scale’s position. Response speed is unlimited. The caliper has SPC (Statistical Process Control) Data Output capability for manufacturing quality control. It outputs data using a serial data cable interface to a computer or other dedicated recording device using SPC Cable with Data Switch (959149 or 959150, depending on cable length required; sold separately). It draws 1/4 the battery power when switched on and about 1/8 the battery power when switched off compared to other digital calipers. The SR44 silver oxide cell battery (938882) lasts for approximately 20,000 hours (3.5 years) of continual normal use and is recommended to maintain constant voltage levels.
A digital caliper is a measuring instrument commonly used for inspection in manufacturing. It has two pairs of jaws on one end attached to a long beam with a marked scale. It takes and displays measurements in both English and Metric units with high-resolution and gearless precision. It comes from the basic caliper, a device used to measure the distance between two opposing sides of an object. The digital caliper allows for the same sort of differential measurements as the dial caliper by zeroing the display at any point along the slide. However, its LCD has replaced the analog dial of the dial caliper with an electronic digital display of the measurement reading as an easily read single value. A digital caliper is commonly used in fields such as metalworking, mechanical engineering, machining, carpentry, and medicine.
Founded in Tokyo in 1934, Mitutoyo is a leader in the metrology field, producing high-quality measurement products including mechanical, dimensional gauging products, focusing on micrometers, calipers, indicators, and other measurement tools, as well as output gauges, interfaces, data collectors, and analysis software. Mitutoyo formed Mitutoyo America Corporation in 1963, which is headquartered in Aurora, Illinois, with additional locations in the U.S. and Canada.What’s in the Box?
- One SR44 silver oxide cell battery
- Storage case
Check Price Now!!
Mitutoyo 500-506-10, Digimatic Digital Caliper, 0 - 24"/600mm, .0005"/0.01mm, with SPC Output Features
- Longer upper and lower jaws, for measuring larger items
- Hardened stainless steel construction, for protection of caliper and ABSOLUTE linear encoder technology components
- Three-way measurement capability, for multiple applications: outer diameter (OD), inner diameter (ID), and step
- Large, digital, single-value readout LCD display, for readability
- Function control buttons on the face, for ease of use: Inch/Metric, Origin, On/Off, and Zero/ABS (Absolute Scale)
If this Information is Not Updated, Please Check!!!
My web is participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provice a means for sites to earn advertising fees by advertising and linking to amazon.com
"CERTAIN CONTENT THAT APPEARS
Related Products
Burner Covers Electric Stove Shopping Digital Blood Pressure Monitor Bestseller Table Gas Stove Low Price
No comments:
Post a Comment